IPv6 (Cisco) Training - Using the "DNS server and a domain name (IPv6)" Commands

Well, since this article is a kind of long I'm going straight down to it, so without further ado let us begin.

The "DNS - server" (IPv6) command, a Cisco IOS "DHCP for IPv6 pool configuration mode command is used to specify the network Domain Name System (DNS) server IPv6 (s) available on one.

Here is the correct syntax and example of the "DNS - server" (IPv6) command:

Syntax: router (config-dhcp) #> DNS - Server IPv6 address
Example: Router (config-dhcp) # dns - server 2001:0 DC8: 3000:3000:: 42

Note that the router prompt "DHCP for IPv6 pool configuration" mode argument is the IPv6 address and IPv6 address of the DNS server available.

Now, in case you're wondering if you can use (configure) the "DNS - server" (IPv6) command several times on a router, if you have multiple DNSnetwork servers. And the new IPv6 addresses delete (overwrite) the current (old) IPv6 addresses.

Also, if you search for a specific DNS server for the list of DNS servers, all you have to do is type the word "no" in front of the command as you can see below:

-Address-dhcp) # no DNS - server config ipv6 Syntax: router (
Example: Router (config-dhcp) # no DNS - server2001:0 DC8: 3000:3000:: 42

Ok, that basically sums up the "DNS - server" (IPv6) command, so, go to "domain name" (IPv6) command.

The "domain name" (IPv6) is also a command from Cisco IOS "DHCP for IPv6 pool configuration" mode command, but is used to configure a domain name for a DHCP client for IPv6, also known as a router or an applicant RR.

Here is the correct syntax and example of the "domain name" (IPv6)command:

Syntax: router (config-dhcp) # domain domain
Example: Router (config-dhcp) # domain ittechtips.com

Announcement that the router prompt is still "DHCP for IPv6 pool configuration" mode and domain of the argument concerning the domain name is used by the client. So in the example above, the router (client) uses the domain name ittechtips.com.

And, like the "DNS - server" (IPv6) command, the "domain name" (IPv6)command can be used (configured) multiple times on a router. And, new domain names do not delete (overwrite) the existing domain names.

Finally, if you delete a domain name to a DHCPv6 client (RR) should see the word "no" to the "domain name" (IPv6) command as shown below:

Syntax: router (config-dhcp) # no domain domain
Example: Router (config-dhcp) # no domain ittechtips.com

I hope this article is very informativeand helped you quickly understand the use of "DNS - server and the domain name" (IPv6) commands. If you need to learn, I suggest you go to my website, where the latest information on Cisco IPv6 design and deployment techniques available.

To your success,

Thanks To : Blank DVDs Store. LOWER Prices in The Same Item Network Consulting

IPv6 (Cisco) Training - Using the "dns-server and Domain-name (IPv6)" Commands

Well, since this article is sort of lengthy I'm going to get right down to it; so without far ado let's begin.

The "dns-server" (IPv6) command, is a Cisco IOS "DHCP for IPv6 pool configuration" mode command that is used to specify the Domain Name System (DNS) IPv6 server(s) available on a network.

Below is the correct syntax and example of the "dns-server" (IPv6) command:

Syntax: router(config-dhcp)#dns-server ipv6-address
Example: router(config-dhcp)#dns-server 2001:0DC8:3000:3000::42

Notice, that the router's prompt is in "DHCP for IPv6 pool configuration" mode and the ipv6 address argument is the IPv6 address of the available DNS server.

Now, just in case if you were wondering; you can use (configure) the "dns-server" (IPv6) command multiple times on a router, if you have multiple DNS servers on your network. And, the new ipv6 addresses will not erase (overwrite) the existing (previous) ipv6 addresses.

Also, if you need to remove a specific DNS server from the DNS server list; all you need to do is type the word "no" in front of the command like you see below:

Syntax: router(config-dhcp)#no dns-server ipv6-address
Example: router(config-dhcp)#no dns-server 2001:0DC8:3000:3000::42

Ok, that pretty much sums up the "dns-server" (IPv6) command; so, let's move on to the "domain-name" (IPv6) command.

The "domain-name" (IPv6) command, is also a Cisco IOS "DHCP for IPv6 pool configuration" mode command; but it's used to configure a domain name for a DHCP for IPv6 client, which is also known as a Requesting Router or RR.

Below is the correct syntax and example of the "domain-name" (IPv6) command:

Syntax: router(config-dhcp)#domain-name domain
Example: router(config-dhcp)#domain-name ittechtips.com

Notice, that the router's prompt is once again in "DHCP for IPv6 pool configuration" mode and the domain argument is specifying the domain name to be used by the client. So, in the example above the router (client) is going to use the domain name ittechtips.com.

And, just like the "dns-server" (IPv6) command; the "domain-name" (IPv6) command can be used (configured) multiple times on a router. And, the new domain names will not erase (overwrite) the existing domain names.

Lastly, if you need to remove a domain name from a DHCPv6 client (RR); you must type the word "no" in front of the "domain-name" (IPv6) command like you see below:

Syntax: router(config-dhcp)#no domain-name domain
Example: router(config-dhcp)#no domain-name ittechtips.com

I hope this article was very informative and helped you quickly understand the usage of the "dns-server and domain-name" (IPv6) Commands. If you need to learn more; I suggest you visit my website, were you'll find the latest information regarding Cisco IPv6 Design and Implementation Techniques.

To your success,

Related : Wireless Barcode Herniated Disc Neck HDMI Cables Store